KSP2222A TRANSISTOR DATASHEET PDF

KSPA Transistor Datasheet pdf, KSPA Equivalent. Parameters and Characteristics. NPN Epitaxial Silicon Transistor. Absolute Maximum RS=IKΩ, f=1KHz. 4. dB. KSPA Design. This datasheet contains the design specifications for. The KSPA is manufactured in a plastic TO case. When looking at the flat side with the leads pointed downward, the three leads emerging from the.

Author: Majar Zoloramar
Country: Algeria
Language: English (Spanish)
Genre: Marketing
Published (Last): 14 January 2009
Pages: 329
PDF File Size: 15.26 Mb
ePub File Size: 6.75 Mb
ISBN: 552-3-13530-679-8
Downloads: 1569
Price: Free* [*Free Regsitration Required]
Uploader: Mukree

The capacitors C1 and C2 are simply used for filtering purpose. One of the most default and primary function of a transistor is to act as a switch.

KSPA Transistor Pinout, Features, Equivalent & Datasheet

The jsp2222a R1 is called the Base resistor and is very important to drive a transistor, it limits the base current and failing to use one might damage the transistor permanently. Another Common application of a Transistor is as amplifiers.

To bias a transistor we have to supply current to base pin, this current I B tranzistor be limited to 5mA. KSPA can allow collector current upto mA and also has power dissipation of mW which can be used to drive larger loads than compared with BC However this type of amplifiers have many drawback and if you are datashfet for some serious amplification applications then you should look into Op-Amps which are nothing but a package of many transistors put to gather with amplification as its sole purpose.

  CHARLES RYRIE SYSTEMATIC THEOLOGY PDF

The resistor R2 is transistkr to limit the current though the collector of the transistor and is not mandatory.

KSPA is a NPN transistor hence the collector and emitter will be left open Reverse biased when the base pin is held at ground and will be closed Forward biased when a signal is provided to base pin.

KSPA has a gain value of tothis value determines the amplification transisyor of the transistor. When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. There are many types of amplifier circuits that are possible with transistor but this is the most commonly used one because it is very good in amplifying low frequency voltage signals like audio signals.

Ks;2222a transistor has a gain h FE associated with it, which can be used ,sp2222a amplify voltage or current. Applications General purpose NPN transistor Can be used to switch high current upto mA loads It can also be used in the various switching applications.

The base pin of the transistor has to be biased with a voltage; this voltage is provided by the potential divider network formed by the resistors R4 and R6.

It is very similar to a mechanical switch but here we will control the switch using electric signals.

KSP2222A Datasheet, Equivalent, Cross Reference Search

In this type of circuit, the Emitter and the Base pin of the transistor should be commonly connected to a same voltage, so we have connected it to the Ground potential using two resistors R4 and R3. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region.

  LCR-9073 A PDF

TL — Programmable Reference Voltage. So if you looking for an NPN transistor that could switch loads of higher current transiztor KSPA might the right choice for your project.

Submitted by admin on 24 June The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.

Normally this type of transistor will either be used as a switch or as an amplifier, both of which is discussed below. Transistor as Amplifier Another Common application of a Transistor is as amplifiers. The vales of the Resistor in the above image are only for reference and are not accurate.

Again the values of the resistor mentioned above are only for reference commonly used you have to design your own circuit based on the application and transistor you are using. But there are two important features that distinguish both.

The transistor will begin to conduct when the voltage across the Base and Emitter pin exceeds 0.